Modeling of the EHD effects on hydrodynamics and heat transfer within a flat miniature heat pipe including axial capillary grooves

A numerical model for an electrohydrodynamic (EHD) grooved Flat Miniature Heat Pipe (FMHP) is developed. Two microchannel shapes are considered as axial capillary structures: square and triangle grooves. For both groove shapes, the electric field affects the liquid-vapor radius of curvature which decreases in the condenser and increases in the evaporator under the action of the electric field. The liquid and vapor velocities are also affected by the EHD effects. The electric field effects on the velocities depend on the FMHP zone. It is also demonstrated that the electric field increases the vapor pressure drop; however, it decreases the liquid pressure drop. The liquid-wall and vapor-wall viscous forces as well as the shear liquid-vapor forces are affected by the electric field. The analysis of the electric forces shows that the dielectrophoretic forces which act on the liquid-vapor interface are predominant and their order of magnitude is much higher than the Coulomb forces. Finally, it is also demonstrated that the capillary limit increases with the electric field for both groove shapes.     

Multiphase Flow Regime Characterization and Liquid Flow Measurement Using Low-Field Magnetic Resonance Imaging

Multiphase flow metering with operationally robust, low-cost real-time systems that provide accuracy across a broad range of produced volumes and fluid properties, is a requirement across a range of process industries, particularly those concerning petroleum. Especially the wide variety of multiphase flow profiles that can be encountered in the field provides challenges in terms of metering accuracy. Recently, low-field magnetic resonance (MR) measurement technology has been introduced as a feasible solution for the petroleum industry. In this work, we study two phase air-water horizontal flows using MR technology. We show that low-field MR technology applied to multiphase flow has the capability to measure the instantaneous liquid holdup and liquid flow velocity using a constant gradient low flip angle CPMG (LFA-CPMG) pulse sequence. LFA-CPMG allows representative sampling of the correlations between liquid holdup and liquid flow velocity, which allows multiphase flow profiles to be characterized. Flow measurements based on this method allow liquid flow rate determination with an accuracy that is independent of the multiphase flow profile observed in horizontal pipe flow for a wide dynamic range in terms of the average gas and liquid flow rates.     

高炉冲渣水余热回收的可行性研究

根据高炉冲渣水的余热特点,提出了一个采用分离式热管换热器的余热回收的方案。文中对余热回收方案中换热设备的结构特点进行了描述。     

Waterhammer modelling of viscoelastic pipes with a time-dependent Poisson's ratio

Poisson's ratio in viscoelastic materials is a function of time. However, recently developed waterhammer models of viscoelastic pipes consider it constant. This simplifying assumption avoids cumbersome calculations of double convolution integrals which appear if Poisson's ratio is time-dependent. The present research develops a mathematical model taking the time dependency of Poisson's ratio into account for linear viscoelastic pipes. Poisson's ratio is written in terms of relaxation function and bulk modulus which is assumed to be constant. The relaxation function is obtained from creep function given as the viscoelastic property data of pipe material. The results obtained from the present waterhammer model are compared with the experimental data for two different flow rates. The comparison reveals that with the application of the time-dependent Poisson's ratio and unsteady friction, the viscoelastic data of mechanical tests can directly be used for waterhammer analysis with less need for the calibration of the flow configuration. It was also shown that the creep curve calibrated based on the present model is closer to the actual creep curve than that calibrated based on previous models.     

LOM and HOM damping study in a superconducting deflecting cavity for ALS at LBNL

Superconducting deflecting cavities can be used in synchrotron light source to generate subpicosecond X-ray pulses while the impedance of the lower order modes (LOM) and higher order modes (HOM) in the cavity should be kept below an accepted level to avoid beam instability. These modes can be damped by adding waveguide on beam pipe. Detailed simulation of Q in CST Microwave Studio is introduced and experiment results on an aluminum model cavity with damping waveguide are reported to make a comparison.     

A Polynomial Time Approximation Scheme for the Grade of Service Steiner Minimum Tree Problem

In this paper, we present the design of a Polynomial Time Approximation Scheme (PTAS) for the Grade of Service Steiner Minimum Tree (GOSST) problem, which is known to be NP-Complete. Previous research has focused on geometric analyses and different approximation algorithms have been designed. We propose a PTAS that provides a polynomial time, near-optimal solution with performance ratio 1+. The GOSST problem has some important applications. In network design, a fundamental issue for the physical construction of a network structure is the interconnection of many communication sites with the best choice of the connecting lines and the best allocation of the transmission capacities over these lines. Good solutions should provide paths with enough communication capacities between any two sites, with the least network construction costs. Also, the GOSST problem has applications in transportation, for road constructions and some potential uses in CAD in terms of interconnecting the elements on a plane to provide enough flux between any two elements.     

校园网络数据资源分层访问策略

分析了校园ＭＩＳ及数据资源的特征,针对校园信息资源范围广、关联复杂的状况,提出了数据资源统一访问策略——分层访问．数据访问分为七层,各层完成数据访问独立性的特定功能,使不同的访问软件能透明访问全部数据资源．为保证传统应用能基于网络计算访问统一数据资源,又提出了“数据访问管道”和数据库访问服务器的技术．文章分析了以应用服务器为基础的Ｎ－Ｔｉｅｒｓ计算的弊端,设计了“虚拟应用服务器”ＷＵＶ－ＡＰＰＳ,将数据访问对象构造成数据对象组件．     

金属光栅表面增强喇曼散射TE模的计算分析

以纳米量级金属履带矩形光栅为模型,研究了表面增强喇曼散射的特性.针对TE模的入射光,采用耦合波原理对金属表面的衍射场进行了讨论,并用数值计算方法讨论了光栅周期、光栅深度等参量对表面增强的影响以及增强因子随第一级瑞利系数的变化关系.结果表明：在入射光波长为700 nm、光栅周期p=400 nm、 光栅深度d=150 nm、占空比为1/3、入射角度为10°时,获得最大增强,增强因子G可达102.     

脉动热管的毛细管结构和尺度效应实验研究

脉动热管的毛细管结构变化如何影响其性能是研究者关注的问题.本文对毛细管截面为正方形和正三角形,水力直径范围为1 mm左右的回路型脉动热管的传热性能进行了实验研究.结果表明,角管脉动热管的倾角变化时,底加热明显优于顶加热;三角形截面脉动热管的热阻比正方形截面脉动热管的热阻更低.脉动热管在水力直径为1.5 mm时比1mm时的性能要好.实验研究为理论分析打下了基础.     

矩形波导栅慢波系统的实验研究

 从实验上研究了矩形波导栅慢波系统的色散特性及其耦合装置的驻波系数，用分布加工的方法分别制作了矩形、燕尾形、梯形3种不同槽形的矩形波导栅慢波结构模型和带输入输出结构的矩形波导栅慢波结构实体模型。采用谐振法测量它们的色散特性和驻波系数，实验结果与理论计算值和模拟值吻合良好。